A new agitator can then be put in place by following the directions in the new agitator's manual. It should use the same methods to be replaced, but it may have a different set of washers, bolts and nuts that are suggested to use for optimal performance of the new part in the old washing machine. It depends on what model Maytag washer you have. If you have an Atlantis or Performa model Maytag you remove the agitator by, first, pulling the agitator cap and softener dispenser off. Locate the bolt on the center post and and loosen. The agitator will pull straight up to remove.

Exclusive TurboRinse system power-rinses away residue so whites stay white and the HydroFlex Plus agitator provides 70% more wash area to clean even bigger loads; triple-spiral design rotates clothes deep into the cleaning zone. Six Fabric-Sort cycles allow you to customize each load based on fabric type for improved clothes care and CorrecTemp control, which is an automatic temperature control assures accurate warm water temperatures to activate detergents. Spot-Treat/Finger Faucet allows you to pretreat stains right at the washer.

Trying to wash your clothes but your washing machine will not agitate or wash? If your washing machine fills with water but then stops, here is the best tip to fix it fast. If you have a top loading washer, the MOST likely part to have failed is the LID SWITCH. Before anything make sure that you have the lid shut. The machine will not run if the lid is open. This is a safety feature so the machine will not agitate with the lid in the open position.

Many times we can get into a rush and forget to shut the lid. If you have the lid shut and the machine has only filled with water and stopped, read on below. (If your washer is NOT SPINNING DRAINING,.) Your top load washing machine has a safety feature built in that will not let it agitate or wash if the lid is open. If the lid switch in your washing machine goes bad, the washer will think the lid is in the open position. Programmu dlya modelirovaniya prichesok.

This will cause the machine to not do anything after it fills with water. If the lid switch is bad, having the lid either open or closed will make no difference. If the washing machine has power, has filled with water, then stops, makes no noise, then the lid switch is most likely the part that needs replaced.

Pyatrusj brouka a ti idzi vodguk. Blueberry3D consists of a standalone to entirely build the database from GIS & elevation data, imagery and OpenFlight objects and a for the real-time application development. Since v4, it also includes a that brings same Hi-Res Terrain and content to CGFs or Physics engines.

The best thing to do at this point is to get the make and model number of your washing machine and type it into Google. Write the words “lid switch” after it and find the exact part for your machine online. Order it next day air and install it with the instructions included. If this did not fix your washer, there is another part that has failed. VIDEO: Troubleshooting why your washing machine is not agitating.

The lid switch is the most likely part to fail in this circumstance. However, this is only the most likely and there may be another part at fault. Here is a short list of ALL the parts in your top load washer that may have failed (and caused your particular problem) in alphabetical order • Cycle Selector Switch – The cycle selector switch controls the speed of the motor and if it goes bad it can stop the motor from operating. • Drive Belt – If the belt falls off or becomes worn the transmission will not turn and the machine will not agitate.

The machine will make a humming noise as the motor will be running. • Drive Motor – This motor turns the agitator and drum to wash your clothing. If it goes bad the machine will not agitate. • Lid Switch – The lid switch makes it so if the lid is opened, the machine will not run. A bad lid switch will make it so power cannot get to the drive motor. • Timer – The timer supplies power to turn the motor. If the timer is defective, the motor will not turn therefore no washer agitation.

• Water Level Switch – The water level switch (aka Pressure Switch) controls the water level. If defective the motor may not receive power. These are the most likely parts that may have failed due to the issue we have explained above. Use safety precautions when doing any type of maintenance checks on your washer. Not all top loading washing machines work in the same way. Some have different parts and operating functions. This guide shows the most basic and general method of fixing most top load washers.