• Servicing Instructions Type C Boilers G.C.N: 47-116-14 47-116-15 LEAVE THESE INSTRUCTIONS WITH THE END-USER Country of destination: GB. • TABLE OF CONTENTS SERVICING INSTRUCTIONS EPLACEMENT OF ARTS ENERAL CCESS - Removing the front panel - Removing the sealed chamber frontal cover - Removing the side panels CCESS TO THE OMBUSTION HAMBER - Removing the combustion cover - Removing the burner and jets - Removing the electrodes - Removing the main heat exchanger - Removing the air pressure switch. The control panel moves downward and when pulled forward, SERVICING INSTRUCTIONS rotates on two lateral hinges; the panel stays in a semi- horizontal position, which allows access to the inner parts of To ensure efficient safe operation, it is recommended that the the boiler (F. • Removing the sealed chamber frontal cover Removing the side panels 1. Remove the screws “C” (F. Remove the four screws “D” for each side panel (F.1.8); 2. Lift the sealed chamber frontal cover from the locating pins 2.

• CCESS TO THE OMBUSTION HAMBER Removing the combustion cover 1. Remove the screws “E” (F. Lift off the combustion cover. 1.12 78 eps Removing the electrodes Before carrying out this procedure, unscrew and slide the burner forward (see previous section). Remove screw “H” (F. 1.15); Removing the main heat exchanger 4. Gently slide the electrode downward (F.

Download free Centrala Termica Ariston Microtec 23 Mffi. Mount install recent search washing dryer machine aml lave linge al tfr hotte hes wse shop argd argf. Forumul Centrale-termice. Este modelul Ariston Microtec 23 MFFI. Si eu am tot acest model de centrala,a mea functioneaza bine,insa dupa aproximativ.

Drain the boiler of water; 2. Release the overheat thermostat sensor “I” (F. Release the two connection nuts “J” connecting the exchanger to the flow and return pipes (F.

• Removing the air pressure switch Removing the fan 1. Disconnect the electrical connections “K” and silicon pipes 1. Disconnect electrical connections “N” and silicon pipes “L” from their connection points (F. 1.20); “O” (F.1.23); 2. Remove screws “M” on the top of the sealed chamber 2. • ERVICING AND EMOVAL OF THE ALVE Setting the minimum and the maximum power of the boiler Setting the gas pressures 1.

Check that the supply pressure to the gas valve is a minimum of 20 mbar for natural gas. To do this, remove the screw “A”. Fit the pipe of the pressure gauge to the pressure connection of the gas valve “B”. • Regulating the heating power for natural gas (G20) model 23 model 27 CG007A Regulating the heating power for butane gas (G30) model 23 model 27 CG008A Regulating the heating power for propane gas (G31) model 23 model 27 CG009A “A” ABLE 2.01 Kg/h 2.00 Kg/h. • Removing the spark generator 1.

Disconnect ignition leads “T” by pulling upward. Remove the screw “V” (F. Remove the spark generator (F. The foundations build me up buttercup torrent download. 61.eps Soft-light Max Heating Adjustment Adjustment VR015A.eps. 1.27 45.eps 10. • Removing the gas valve CCESS TO THE ATER IRCUIT 1.

Disconnect all the cables from the solenoid and Important! Before any component is removed, the boiler modureg; must be drained of all water. Remove the spark generator (see previous section); 3. • Removing the safety valve Removing the main circuit flow switch 1. Loosen nut “Z” (F. Unscrew and remove the valve (F.

Remove the cable of the main circuit flow switch “B1”. Remove the screws “C1” (F. • Removing the pump 1. Remove the U-clip “ D1” (F.

( 17:11) skachat' knigi igra prestolov po poryadku besplatno, za vzyatie berlina skachat' besplatno, fishdom 3 skachat' besplatno torrent, skachat' besplatno s. ( 19:51) skachat' kartu rossii garmin nuvi, skachat' kartinki dlya nokia 6303i classic, gruppa kombinaciya video skachat' besplatno, besplatnye knigi skachat' igra prestolov, blekdzhek igra ili professiya skachat', vaz 11183 lada kalina remont svoimi rukami skachat', timati i g. Chertezhi tankov dlya modelirovaniya iz dereva.

Remove the retaining clip “E1” (F. Remove the U-clip “ F1” (F. Release the nut “G1” (F. Remove the pipe “H1” (F. • Removing the pressure gauge Removing the expansion vessel 1. Remove the U-clip “J1” and remove the pressure gauge 1. Loosen nuts “K1” and remove the gas pipe (F.

1.50); coupling (F. Loosen nut “L1” (F. • Removing the overheat thermostat Removing the D.H.W.

Temperature sensor (N.T.C.) 1. Disconnect overheat thermostat electrical 1. Pull off the electrical connector “Q1” and unscrew the connections “N1” (F. 1.54); sensor probe using a suitable spanner (F. Then remove the thermostat from its mounting by releasing the securing clip (F.